Team,
Just an update, I sent off the stator for testing and they re-round it. Total cost was $180.00

Unfortunately…. No wait, fortunately! I just found out we’re having our third kid. I also just...

Hey team,
I'm running a 2010 G450x. It's about about 8k miles. I've replaced the stator flywheel bolts (Don't worry, Tim). But, I'm experiencing some charging system woes. I was out of a great ride...

I did that a a week ago & that helped! Thanks, man.

Hey Allroad,
Thanks for the reply. Sounds like I'm in the same ballpark. I should have compared it to the RPM and did a chart-graph. I'm guessing I just need to adjust my TPS sensor more to...

Hey team,

Quick request for help! If anyone has a GS-911, can you pull your reading for the 450x’s “Idle Actuator Position”? Mine is between 17*and 21.5*

I did some work on the TPS and I...

So, new battery-good start.

Can you hot-wire (jumper cables) the battery directly to the starter? See if that turns it.

Odd ball possibility, make sure you have oil in the bike…. (It’s happened...

Someone asked me what sensor I used, it’s this one:

https://www.ebay.com/itm/163952123297

I had a paragraph removed because ADVrider didn’t want start a beef Motorcross Action magazine. But, this was one of the sections o realt wanted included:

“There is an article in Motorcross Action...

Hey team,
Wanted to pass on my write up on the 450x and her sisters.

https://advrider.com/revisiting-the-bmw-g450x-g650x-and-hp2/

ahoy,
The plug isn’t coded, it’s just a line of connectivity. As long as the loop is completely it’ll be activated. You can rig up a switch and it’ll work.

It was originally located on the...

Got the engine back together! Unfortunately, I’ve got to go out of town for 10 days. So I’ll have to mount it when I get back.

Belay my last!
An impact driver got the job done.

Got the old TL out. Right side case s was a bit harder than anticipated.

I don’t think I’m the first guy in here. Were the first fella to...

Any trick to remove the clutch basket nut? I took off the ride side and grabbed on to the stator nut, but the thing is jammed.

374399

Engine is out!

The left bottom mount was a bitch.

The swing arm pivot rod was well greased and the bearings were FAG. Still fresh. Someone loved this bike at some point.

Hoping to install...

It’s two wires: (1) Blue/Brown (2) Brown

Ahoy,
Got my torque limiter on Friday, It appears to be the older A model. With only 223.9 NM limit. //lame// I called up BMW and asked if they could get me a higher torque device. They again told...

Got the part!

Apparently, this is the last Torque Limiter in the world according to Max BMW and western BMW. If true, a sad fact.

We’ll need to establish a process to rebuild the part, I know...

Torque limiter....a second time? [xx(] [xx(][xx(][xx(][xx(][xx(][xx(]

Howdy! No, it's not as tough as I initially thought it was...just had to put minimal thought into it. hahaha. I've dropped engines and trannies from motorcycles before and I was accustom to knowing...

Solid advice. I was hoping that when the BMW engineers were developing this unique and novel bike they would also develop an equally novel manner of removing the engine without resorting to wood...

Hey team,
I’m just about the pull the motor and swap out the torque limiter. I’m looking for a “how to” guide. I have reprom, but it’s not the most detailed.

I have a 300 lbs motorcycle floor...

374165374167374165374167My phone was giving me trouble. Had to break out the laptop and upload the pictures.

Hey team, recently stopped my dealership to pick up parts, the tech gave me a PROMOTIONAL copy of the BMW book.

Sure enough, the little g450x was given a feature.
I’ll post up some pics.

Results:
I took out the clutch plates. Really easy job, took about 30-45 minutes start to finish. I took pictures & will post them up later in the event they help anyone in the future.
In short,...

Response:
Tim! Appreciate you pulling that information for me. I need to get my hands on the Husky Shop Manual…provided the gaps of information in the BMW REPROM, it seems like it would be helpful...